您好!歡迎光臨廣東匯佳電子科技有限公司,您是第 3821 位訪客!
2019年12月08日 15:52 | 客戶登錄
數碼鐘 >> 返回 您當前所在位置:首頁 > 產品展示 > 數碼鐘 > 正文

MT1138A

更新時間:2016-02-17 09:39:33點擊次數:1074次字號:T|T
相關介紹
MT1138方形圓角木頭鐘使用說明書(V1.2)
概述:
本產品采用時尚LED顯示元素,能顯示小時、分鐘、溫度,具有時間、溫度、鬧鈴、貪睡、日歷、查詢、12/24小時制、亮度減半、省電等功能,4個按鍵,雙電源供電,
備份電池。可放置在床頭、書桌、客廳、客房、病房等地方,可作計時、定時、鬧鈴、測溫等作用,產品大方美觀、安全、環保、時尚、實用。
功能介紹:
?顯示時間、溫度,時間、溫度自動切換顯示,可查詢月、日,初始上電為2012年1月1日12:00:00;
?12/24小時制:可以進行12/24小時轉換,默認值24小時制;
?4個按鍵操作:MODE鍵,SET鍵,UP鍵,DOWN鍵;
?鬧鈴功能: 鬧鈴時間到時響鬧一分鐘聲音為“嘀嘀 嘀嘀”,在響鬧狀態下按任意按鍵都可停止響鬧;
?貪睡功能:在鬧鈴響鬧狀態下,若無任意按鍵,則5分鐘后鬧鈴繼續響鬧(共4次);
?省電功能:正常模式下按住MODE鍵3秒關閉LED顯示,進入省電模式;
?亮度自動減半功能,顯示亮度在晚上10:00至早上6:00將自動減半;
?查詢功能:在正常走時狀態下,按MODE鍵可查詢月、日、鬧鈴溫度;
?日歷功能:從2000年1月1日到2099年12月31日;
?溫度測量范圍:-30℃~50℃;
?雙電源供電功能,在外部電源斷電后仍可走時,但無鬧鈴顯示,也可用4節5號堿性電池供電通過背面開關來切換供電;
操作步驟:
1、安裝:拆開包裝請將本產品附帶的DC變壓器插到220V/50Hz照明電路上(電壓通用范圍100V—240V 50Hz/60Hz),DC/6V插到該產品的DC插座,
產品進入自檢,自檢無誤后有“嘀”聲,顯示12:00:00,進入正常走時狀態,52秒后自動切換溫度顯示,再8秒后自動切換回時間顯示。
2、SET鍵操作:
◆在正常顯示狀態下,按SET鍵進入設置狀態,被設置值閃動,設置順序為:時→分→年→月→日→鬧鈴時→鬧鈴分→退出。
3、UP鍵操作:
◆在正常走時狀態下,按UP鍵開啟/關閉鬧鈴。
◆在正常顯示狀態下,按住UP鍵3秒,可切換固定時間、時間\溫度轉換顯示;
◆設置狀態下,按UP鍵上調被設置值,按住不放可快速上調。
4、DOWN鍵操作:
◆正常走時狀態下,按DOWN鍵切換12/24小時制模式顯示,在12小時制的模式顯示下,下午時間PM燈亮。
◆設置狀態下,按DOWN鍵下調被設置值,按住不放可快速下調。
5、MODE鍵操作:
◆正常走時狀態下,短按MODE鍵切換時分/月日/鬧鈴/溫度顯示;長按MODE鍵3秒可以關閉顯示(內部時鐘仍在走時)進入省電模式,再按MODE鍵可返回正常顯示模式。
◆設置狀態下,按MODE鍵退出設置狀態,返回正常顯示模式。
其他信息:
1:產品尺寸:長X寬X高=210X90X48毫米
2:外包裝尺寸: 長X寬X高=265X126X85毫米
3:產品凈重: 298克     毛重:425克
4:產品的功耗:1.8瓦(紅色LED),0.8瓦(白色LED)
5:電源輸入電壓: AC 50Hz/60Hz 100V-240V   產品輸入電壓:DC6.0V
注意事項:
1:產品背后伸出的兩黑線,線頭的黑點是溫度探測傳感器,要求注意放置,不能用力拉扯,否則容易損壞。
2:當使用AA1.5X4的電池供電時,請將后面的撥動開關從“1”位撥到“2”位;使用DC6.0V供電時,該撥動開關從“2”位撥回到“1”位。
3:當拔電后,時間無記憶,要求更換CR2032鋰電池,可以在正常走時狀態下更換。
產品保證與維修:
本產品若遇質量問題,請與經銷商聯系或登錄網站http://www.mtclock.com,把您的問題反映給我們。

MT1138 Square Fillet wooden clock manual(V1.2)
Summary:
MT1138 wooden clock uses LED displayer , It can display time and temperature; it has such as alarm, snooze, calendar,12/24 hour etc functions,. 4 keys operation and two power supply,
.     This clock can use in fashionable, safe and practical. It is fit for placing in the front of bed, on the desk, in the living room, in the sickroom and so on.
Features:
◆Directly show time and temperature. This two display mode switches automatically. And show month and day indirectly. Show 12:00:00 when first connected to power with January 1st, 2012;
◆12/24 hour display mode ,can be converted,  default: 24 hours;
◆4 keys operation: MODE key, SET key, UP key and DOWN key.
◆Alarm function: the alarm sounds from transducer for one minute, "DiDi DiDi". The alarm can be turned on or off directly. When the transducer is alarming, pressing any keys can be stop;
◆Snooze function: if there’s no key pressed when the alarm transducer is sounding, the alarm transducer will sound after 5 minutes (total 4 times);
◆Sleep function: in normal display mode, pressing MODE key for long 3 seconds will close the led display and let the wooden clock enter into sleep mode;
◆For MT1108, the brightness in the night 10:00 to 6:00 in the morning will be halved.
◆Seeing function: in normal display mode, pressing MODE key shortly can see date, alarm and temperature.
◆Calendar function: from January 1st, 2000 to December 31st, 2099.
◆Testing temperature: -30℃~50℃.
◆Dual power supply, when taking off the external power supply, the internal cell still supplies timer working, but no display and alarm.
◆ It can also use 4 PCS AA batteries by changing the switch in the back panel.
Detailed steps
1、Installation: Please break open the packaging of the product attached to DC transformer into 220V/50Hz lighting circuits (application of the voltage 100V---240V50/60Hz),DC/6V product plug into the DC outlet.
For the first time you use, please be connected to the DC/6V first, then the wooden clock will enter into self-test mode, self-correct after the “DI" sound, and show 12:00. Then the built-in battery out of the
Insulation film, switching automatically show the temperature 3 seconds after displaying the time 8 seconds, and then automatically switch back to the show time.
2、SET key:
In normal display mode, pressing SET key will enter to setting status, the setting value is flashing, the setting order is: hour→minute→year→month→day→alarm hour→alarm minute→quit.
3、UP key:
◆In normal display mode, pressing UP key will turn on or turn off alarm.
◆In normal display mode, holding UP key over 3 seconds exchange time and time/temperature displayer;
◆In setting mode, pressing UP key will upward-adjust the setting value, if pressing UP key for long, the setting value can fast-upward.
4、DOWN key:
◆In normal display mode, pressing DOWN key will convert 12/24 hour display mode. And in 12 hour display mode, the PM indicator light will be lighted between 12:00 and 23:59 which in 24 hour.
◆In setting mode, pressing DOWN key will downward-adjust the setting value, if pressing DOWN key for long, the setting value can fast-downward.
5、MODE key:
◆In normal display mode, pressing MODE key for short will make the display content change among time, date, alarm time and temperature. Pressing MODE key for long 3 seconds will close the led display and
let the wooden clock enter into sleep mode (the internal clock is still going). And then MODE key to open the show.
◆In setting mode, pressing MODE key will quickly exit setting mode and return to normal display mode.
Other features:
1.the size of product: 210×90×48mm
2.the size of outer packing: 265×126×85mm
3.net weight: 298g    gross weight: 425g
4.power consumption: 1.8Walt(red led), 0.8Walt(white LED);
5.AC input: AC100-240V 50/60Hz     DC output: DC6.0V 600mA

Caution:
1.There’re two black lines in the back panel, and the ends of these two lines are connected to a small black dot,
which is the temperature sensor. Please be careful of the position of the sensor, and should not pull it or press it.
2.When using 4 available AA batteries, you should turn the switch from “1” to “2”, the switch is in the back panel; when using the DC6.0V, you should turn the switch back to “1”.
3.Without DC6.0V or 4 available AA batteries, if the time is not going, you should change the CR2302 battery while the DC6.0V or 4 available AA batteries are connected.
Services:
If having any product problem, please contact with the dealer or visit the website http://www.mtclock.com and send your problem to us, thank you!
0 條評論
不想登錄?直接點擊發布即可作為游客留言。
產品展示
Products
聯系方式
020-89287367
投訴電話:13332851028
傳真:020-89285725
地址:廣州市天河區白沙水路162號4樓
關注我們
    
Copyright ? 2003 - 2019 www.ietrvj.tw All Rights Reserved    粵ICP備:09077962   廣東匯佳電子科技有限公司 ? 版權所有
棒球规则